Porsche 914
Parts for Sale

 

  

Parts for Sale


 
Porsche 914 Chassis Repair Panels

Excellent for repairing longitudinal and jack receiver rust. Also extensively used for competition chassis stiffening and large engine installations. The panels are .100 thick (very strong) and extend from front wheel house to the outer rear suspension console. Welding is required. The rear section of the panel sandwiches between the outer suspension console and the trailing arm. Permanently restores door gap and eliminates flexing problems. Provides a base to weld to if additional repair is needed in floors, inner longitudinal, or firewall area. Excellent installation instructions included plus my personal assistance if you have questions. I have been selling and installing these for 28 years. There is nothing on the market for 914 chassis repair that is this strong, proven or easy to install. Porsche repair and restoration expert for 38 years.

Free Shipping.

$340.00

 


 
Porsche 914/4 Cylinder Head Temperature Sensor Extension.

This little device slows down the heating of the sensor and improves warm up drivability.

Free Shipping. 

$22.00

 


 
Porsche 914 Original Style Rear Sway Bar Mounts

Porsche 914 Original Style Rear Sway Bar Mounts

These are rear sway bar mounts I have offered for several years. These are for all 914 and 914/6, 1970 thru 1974. 1975 and 1976 have a different style bracket also available. Almost a perfect copy of the Porsche 914 rear brackets and weld in as the originals. High quality, heavy gauge steel brackets and reinforcement pieces for rear trunk. The location position is simple, an existing hole in the transaxle cross member determines the final position. The reinforcement plate fits perfectly in the ribs in the rear trunk floor.

 Free shipping.

$55.00

 


 
Porsche 914 Front Sway Bar Mount Bracket

This system does not require cutting into the boxed frame area to install. This system provides an original style mount but stronger. The bracket with the upper two captured nuts "sandwich" the inner fender. Mounts in the exact same location as the factory mount. Comes with instructions and 2 bracket sets to install 1 front sway bar.

Free shipping.  

$45.00

 


 
Porsche 914 Floor Pan Air Flaps New Old Stock

Brand new pair of flaps 914.559.163.10 used on the 1973 and later 914's to improve engine cooling. Can be used with all years 914 including the 914/6.  Free shipping.

$45.00

 


 
Rebuilt & Improved Porsche 914/4 Relay Board Harness Clip

Rebuilt & Improved Porsche 914/4 Relay Board Harness Clip

Description:

Rebuilt 914/4 engine compartment relay board. This part is correct for all years 4 cylinder cars. The internal connections on the original relay board were swaged and not soldered, the connections have become loose after many heating and cooling cycles as well as exposed to the elements when the original tar like material on the bottom side of the board cracked and fell off exposing the components the tar was supposed to protect. 

         We completely clean and remove the old tar and have found a special solder to make a permanent repair to all these swaged connections. The bottom side has been repotted in an authentic looking vinyl based moisture proof material for lasting protection.

         NO CORE REQUIRED. These 40+ year old boards are responsible for many electrical maladies including intermittent stalling, charging problems, loss of power to the fuel pump. If you have ever temporarily corrected an electrical problem by simply unplugging and re-plugging a round relay on the board, you need this product!  FREE SHIPPING.

I have 45+ years of  914 service and parts.  If any questions please call          309 694-1797 or email.  Brad Mayeur

$299.99

 


 
Porsche 914, 911 Front Sway Bar "U" Brackets

Porsche 914, 911 Front Sway Bar "U" Brackets

This is a pair of 914 and 911, 1974 thru 1989 front sway bar "U" bracket for lower control arm (transverse link).   The 911 application is needed when the sway bar is changed from under body to thru the body allowing a wide selection of adjustable sway bars to be chosen. The 914's did not have these brackets from 1974 thru 1976 if they were not equipped with the optional sway bars. Perfect copy of the original bracket using .40mm thicker metal with plunge weld holes for easy installation.

 Free shipping!

$30.00

 

 

 

 

 

 

 

 

 

Categories